| 982751901 Liebherr A924B Li Slewing Ring | P55°:2400 kN; P120°:850 kN; J6:490 mm; s:15 mm; Ca:115 mm; A1:190 mm; Appropriate attachment bolt, size G:24 mm; ba max.:108 mm; Locating ring:4 x FRB 10/290; Oil seal:TSD 3038 U; P0°:1900 kN; N1:28 mm; da:170 mm; bc:113.5 mm; Q120°:1800 kN; H1:180 mm; P150°:760 kN; End cover:ETS 3038 R; P90°:1150 kN; P180°:950 kN; |
| 982855501 Liebherr R942 LI Slewing Ring | d:6 mm; r, r1,2 min.:0.3 mm; F:9 mm; B:12 mm; Mass inner ring:0.003 kg; |
| 933628601 Liebherr LH60 C Slewing Ring | Da max.:84.2 mm; Basic static load rating C0:1220 kN; Sealing solution:Triple-lip seals; Da min.:79.7 mm; da max.:68 mm; b1:6.2 mm; Material constant KM:330; Specific dynamic load factor K:100 N/mm²; Design (sliding contact surface combination):Steel/steel, heavy-d; rb max.:1 mm; α:3 °; d1 ≈:68 mm; ra max.:0.6 mm; D:90 mm; r1 min.:0.6 mm; da min.:65.4 mm; b:6.2 mm; M:4 mm; Specific static load factor K0:500 N/mm²; |
| 982752101 Liebherr R944B Slewing Ring | rb max.:1.3 mm; Da min.:55 mm; da max.:44 mm; C:13.5 mm; Calculation factor Y:1.4; Ca min.:3 mm; Cb min.:3.5 mm; r3,4 min.:1.3 mm; Reference speed:8500 r/min; Da max.:56 mm; Mass bearing:0.2 kg; Calculation factor Y0:0.8; T:17 mm; Fatigue load limit Pu:5.4 kN; Dimension series:L 69300; r1,2 min.:3.6 mm; Db min.:60 mm; D:63 mm; B:17 mm; Limiting speed:10000 r/min; |
| 933628601 Liebherr LH60 MT Slewing Ring | Accessories:Two Seals; Basic Static Radial Load Rating Co:13700 N; Fillet Radius ra:0.60 mm; Basic Dynamic Radial Load Rating C:13000 N; Oil Speed Rating Open/Shielded n2:7000 rpm; Sealed Speed Rating n3:3600 rpm; D:100.0000 mm; d:80.000 mm; Grease Speed Rating Open/Shielded n1:6000 rpm; B:10.00 mm; |
| 969331201 Liebherr R944C TU Slewing Ring | Grease Speed Rating n1:6000 rpm; d:35.000 mm; Accessories:One Seal; D:72.0000 mm; Basic Dynamic Radial Load Rating C:39100 N; Fillet Radius ra:1.00 mm; Sealed Speed Rating n3:6000 rpm; B:30.20 mm; Basic Static Radial Load Rating Co:36500 N; Oil Speed Rating n2:8000 rpm; |
| 982751301 Liebherr R904 Slewing Ring | Coefficient of friction µ max.:0.08; D:140 mm; Specific dynamic load factor K:140 N/mm²; Mass bushing:1.17 kg; Specific static load factor K0:200 N/mm²; Permissible sliding velocity v min.:0 m/s; Effective load carrying cross section A:24920 mm²; Coefficient of friction µ min.:0.03; Tolerance shaft:h8; B:180 mm; Tolerance housing:H7; d:155 mm; Permissible sliding velocity v max.:0.5 m/s; |
| 982882001 Liebherr R310 Slewing Ring | Calculation factor f0:14; s1:34.9 mm; Thread grub screw G2:3/8-24 UNF; Hexagonal key size for grub screw N:4.763 mm; d:42.862 mm; Basic dynamic load rating C:33.2 kN; B:42.8 mm; D:85 mm; d2:62 mm; Fatigue load limit Pu:0.915 kN; d1 ≈:56.8 mm; B1:56.3 mm; Mass complete bearing:0.84 kg; C:22 mm; Basic static load rating C0:21.6 kN; Recommended tightening torque for grub screw:16.5 N·m; B4:6.75 mm; |
| 933628601 Liebherr R944C Li Slewing Ring | ra max.:3 mm; rb max.:3 mm; E:310.68 mm; d1 ≈:243 mm; Fatigue load limit Pu:196 kN; d:190 mm; das:235 mm; Mass bearing:35.7 kg; Db max.:324 mm; Limiting speed:1000 r/min; s max.:7 mm; D1 ≈:296 mm; Da max.:325 mm; D:340 mm; r1,2 min.:4 mm; B:92 mm; Reference speed:800 r/min; Basic static load rating C0:1900 kN; Calculation factor kr:0.3; Basic dynamic load rating C:1250 kN; |
| 933816501 Liebherr R934B Slewing Ring | P150°:66.7 kN; H:258.762 mm; Initial grease fill:379.89 g; Ca:72.619 mm; A1:120.65 mm; Cap bolt, SAE grade:8; Appropriate attachment bolt size G:0.75 in; J min.:336.55 mm; P90°:111 kN; R2:30.163 mm; ba:53.975 mm; A2:255.588 mm; RG:1/2 NPT; PG:1/4 NPT; P180°:81.4 kN; H2:53.975 mm; L:419.1 mm; Taconite seal:TER 121; J max.:368.3 mm; Cap bolt:2 x 1-8 UNC; |