| 16258001 Kaydon Slewing Ring Bearings | Dimension H:2.9 in; Bearing Number:MSM65BX; Seal Type:Viton Single Lip; Bearing UPC:013992035110; Bearing - Housing - Seal UPC:013992098160; Series Type:Medium Series; Dimension T:11.3 in; Shaft Size:65 mm; Dimension L:5.4 in; Dimension V:0.1 in; Note:This product line wa; Support Type:Round Flange; Dimension N:7.563 in; Cr - Dynamic Load Rating:37768 lbf; Bearing - Housing - Seal:MSM65BXHRSS; Dimension P:0.6 in; |
| 11-16 0200/1-0811 IMO Slewing Ring Bearings | Dimension D Min:12.56 in; Grease Lubrication - B/C/O Seal:600 rpm; Eng Internal Radial Clearance - Min:0.0053; Dimension A:4.92 in; Oil Lubrication - M/N Seal:900 rpm; Pre Install Clearance Min:0.0053 in; Dimension H:2.00 in; Full Timken Part Number:QVVSN22V315SB; C - Dynamic Load (Basic):125000 lb; Dimension SVV:5.12 in; Dimension J (Bolt Size):0.875 in; Dimension D Max:14.41 in; e - Geometry Factor:0.25; |
| 77262A Franke Slewing Ring Bearings | Ball Type:Ceramic; Design Units:METRIC; D:62 mm; r - Outer Ring To Clear Radius3:1.0 mm; R - Inner Ring To Clear Radius2:1.0 mm; d:30 mm; Bearing Width:16 mm; Da - Outer Ring Backing Diameter:56.0 mm; Contact Angle:25 ยบ; Bearing Weight:0.195 Kg; do - Ball Diameter:9.525 mm; Limiting Speed (Grease):27100 rpm; Ce - Dynamic Radial Rating1:24400 N; Cage Type:CR - Phenolic Outer; da - Inner Ring Backing Diameter:36.500 mm; |
| MTO-210X Kaydon Slewing Ring Bearings | Y - ISO Factor9:2.19; Cone Part Number:2580; db - Cone Backface Backing Diameter:38.61 mm; D:66.421 mm; a - Effective Center Location3:-8.6 mm; Cage Type:Stamped Steel; Ca90 - Dynamic Thrust Rating (90 million revolutions)6:2280 lbf; B:25.400 mm; Db - Cup Backface Backing Diameter:59.94 mm; C90 - Dynamic Radial Rating (90 million revolutions)4:4880 lbf; Ab - Cage-Cone Frontface Clearance:1.5 mm; Bearing Weight:0.4 Kg; |
| 68653A Franke Slewing Ring Bearings | Seal Type:Viton Single Lip; Bearing Number:LSE211BX; Support Type:Two-Bolt Plummer Blo; Dimension H:95 mm; Dimension L:315 mm; Dimension J:260 mm; Dimension H2:208 mm; Bolt Size:2 x M20; Dimension M:90 mm; Cr - Dynamic Load Rating:31024 lbf; Maximum Speed:3310 rpm; Bearing UPC:013992025982; Shaft Size:2-11/16 in; Cor - Static Load Rating:36194 lbf; Series Type:Light Series; Note:This product line wa; |
| RK6-16E1Z Kaydon Slewing Ring Bearings | Dimension S1:23.4 mm; Material:Bearing Steel; Bearing Type:Ball Bearing; Dimension B1:1.469 in; Lubrication Type:Non-Relubricatable; Center of Bearing from End S:13.9 mm; Inner Ring Width B:27.78 mm; Weight:0.50 lb; Dynamic Load Rating:2380 lbf; Sub Series:1..KLLB; Static Load Rating:1070 lbf; Series:Industrial; Outside Diameter D:1.575 in; Dimension B2:0.531 in; Radius r:0.6 mm; Seal Type:Labyrinth Seal; |
| 77315A Franke Slewing Ring Bearings | Chamfer r1smin2:15.0 mm; Lubrication Hole Diameter h:12.0 mm; Chamfer rsmin:3.00 mm; Backing Shaft Diameter ds:648.3 mm; Inner-Ring Set:600ARXS2643; DUR/DOR F/E:660.000 mm; Dynamic Load Rating C11:36120 kN; Backing Housing Diameter Ds:770.0 mm; Outer-Ring Set:660RXS2643A; Number of Lubrication Holes:16; Width B:575.000 mm; O.D. D:820.000 mm; Type:RX-1; Width C:575.000 mm; Static Load Rating Co:14780 kN; |
| 12-20 0541/1-32222 IMO Slewing Ring Bearings | Y - ISO Factor9:1.44; D1 - Flange Outer Diameter:5.1211 in; B - Cone Width:1.0000 in; C90 - Dynamic Radial Rating (90 million revolutions)4:6830 lbf; R - Cone Backface To Clear Radius1:0.14 in; C1 - Dynamic Radial Rating (1 million revolutions)5:26300 lbf; Da - Cup Frontface Backing Diameter:4.87 in; G2 - Heat Generation Factor (Rib-Roller End):41.8; C1 - Cup Flange Width:0.1875 in; Bearing Weight:1.1 lb; |
| 11-20 0541/1-32122 IMO Slewing Ring Bearings | Cg - Geometry Factor:0.0945; Da - Cup Frontface Backing Diameter:5.94 in; Y - ISO Factor3:1.76; e - ISO Factor2:0.34; r - Cup Backface To Clear Radius1:0.130 in; C - Cup Width:1.5000 in; Db - Cup Backface Backing Diameter:5.67 in; Series:755; Cup Part Number:752; Design Units:Imperial; D:6.3750 in; |
| MTE-265 Kaydon Slewing Ring Bearings | e - ISO Factor8:0.41; Ca90 - Dynamic Thrust Rating (90 million revolutions)6:21400 lbf; Cup Part Number:8520; Da - Cup Frontface Backing Diameter:314.96 mm; Design Units:Imperial; Ab - Cage-Cone Frontface Clearance:3.3 mm; Y - ISO Factor9:1.48; Cg - Geometry Factor:0.14; K - Factor7:1.44; G2 - Heat Generation Factor (Rib-Roller End):172.4; Cage Type:Stamped Steel; D:327.025 mm; Series:8500; da - Cone Frontface Backing Diameter:247.90 mm; |